AdammsGallery

Leaking Leaded Glass Windows

Leaking  Leaded Glass Windows If you have older leaded or stained glass windows you may be experiencing leaks. You may see this as droplets forming on the lead came, and dripping down the window, or as a pool of water at the window sill. Remember that water flows down hill, so if you see water anyplace on the window or sill it is most likely coming from a place higher up. After the rain stops and the water dries you will see water marks where the water has dripped. DO NOT CLEAN these off. The dried spots will help us determine where the leaks actually are.     Leaks may be from dried out a flaking putty, or they may be from broken, or missing lead came. On older windows(65-100 years old), the smog and acid rains have disintegrated the heart of the lead came, and in many cases it just falls apart. Also improper repairs lead to weakened windows and cause leaks. If the leaks are caused from dried out and missing glazing putty we reglaze by forcing the new putty into the lead came between the glass and the lead. The right type of putty will last for many years. The correct putty is metal sash putty. It is either black or grey in color, and is oil based. It should not be thinned with paint thinner, or turpentine. This will only dilute it too much, and cause it to dry out and flake. Do not use white putty. It is meant for wooden sash. Also, by all means, DO NOT USE SILICON. Silicon may seal temporarily, but it will make a mess, and only increase the cost of a repair because it has to be cleaned off before a proper repair can be successful.                             Broken Came      If your window is very old and the lead came has gaps, or holes your window probably needs to be removed and releaded. In this case we rebuild your window with your old glass and new lead came. We will also replace any broken, or badly etched(water stained) glass. To reglaze the window we try to clean out as much old dried out putty as we can. Then we force the new putty into the lead channel. After the window is reglazed the putty needs to set up, so we need a few clear days. Otherwise the new putty stands a chance of being washed out in a heavy rain. On a large window it may take two or three applications before the reglazing is successful. Of course if we totally restore your window you will have a quality window that will last many, many years. IF YOU NEED US WE ARE READY !Adamm's Stained Glass   1426 4th St. Santa Monica, CA 90401  310 451 9390  [email protected]

Custom Stained Glass Heart Windows

                         

   Who doesn't like hearts? Quite often we have long time customers that want to add a window or two to their home. Sometimes they have bought a new home and would like a special window for it.Here is another set of windows that we added to the sitting room of a wonderful long time customer. We installed a pair of identical, but smaller heart windows in the bedroom about 7 years ago, and she always wanted to finish the job with more in the sitting room. It turned out that the sitting room was the perfect place. We added the two heart windows by cutting out the mullions and then we replaced all the clear glass with double glue chip for privacy. Now she doesn't need the blinds that disrupted the room, and she has plenty of light.

     The blue glass is bullseye cathedral, red is hand blown Lambert antique, and we used  2" glue chip bevels as the border that we custom beveled for length. We also used 8 1" round faceted jewels around the hearts. She did a great job with the fabric drapery over the windows for a romantic effect.
   It's clients like these that make coming to the studio everyday so enjoyable. 

Triple Pivot Casement Beveled a & Leaded Glass Windows

Beveled Glass Installation

 

      It has been about one year since one of our long time customers approached us about making a set of triple beveled glass casement windows with a center pivot on each. After much back and forth we finalized a relatively simple rectilinear beveled design.

The difficult part was installing the triple casement. Once again I enlisted the help of the best Handyman, and installer I know, Don Van Cura. Don is in my Networking group Wildfire Networking. I wouldn't do any difficult installation without him. I was able to find a perfect all brass, ball bearing, pivot hinge, from Architectual Resource Center  http://brasswindowhardware.com/and the installation of them appeared to be pretty straight forward.

 

                  window before

 

            We understood how the hinge worked, but it took some time before we agreed how to install them.  The owner of the company that sold the hinges didn't have any help with our particular type of installation. We didn't  have the option of removing the jamb to set the top hinge. We ended up removing the ball bearing on the top hinge, and that gave us the extra room for clearance, and didn't affect the ease of pivot since the weight was on the bottom bearing. We set the hinge into the sash. With the ball bearing hinge the pivot was very smooth.

     We first set the center sash,

                                                                                      cutting detail

  

              routing mortise                                  hinge set

and then trimmed the right sash as we needed. Finally we set the left sash. This was an interior set of windows. It was a divider between the master bath and bedroom.

                                                    mortise in sill

   

         bottom hinge set      mortising top hinge          Don with windows installed

 

     After we finished the installation the owner had the sash stained and finished. A very nice and interesting project.